#YAMAHA BOLT ECU FLASH FULL#
#YAMAHA BOLT ECU FLASH FREE#

Smart-Tune-X is intended to conduct this adjustment to achieve maximum performance boost. On new generation fuel injected engines from the early 80's you have been unable to adjust the AFR - in order to add more horsepower to the powertrain - with rejetting, like on carbureted models. This is known as a stoichiometric fuel mix however this is a lean mix as well because of rigorous emission standards the manufacturers have to comply with. Most factory ECU's are set to maintain a 14.7:1 air/fuel ratio. The fuel trim on fuel injected up-to-date motorcycles is controlled by the Electronic Engine Management, also referred to as ECU, or ECM. If the maximum speed is limited by a factory speed limiter, or you are about to overwrite the stock red line RPM limit, then check out our Rev Limiter.

#YAMAHA BOLT ECU FLASH FREE#

If you canвЂ™t find the one applicable to yours, feel free to contact our Tech Support. Smart-Tune-X chip is available for all fuel injected motorcycles controlled by PCM. These bike specific fuel management chips are sorted into numerous categories according to the operating range and type of IAT / MAF / MAP and oxygen (if any) sensor. Yamaha Bolt Smart-Tune-X features new unsurpassed options that allow this remapping chip to far outperform other bike chips. Smart-Tune-X Yamaha Bolt performance chip spoofs engine sensor signals being read by the Electronic Control Unit, resulting in an adjustment to the fuel trim which causes the increase in power output as well as cranks up speeding up and throttle response through the rev range. The power tuner works to optimize the fuel programming for maximum horses and increased throttle response. With Smart-Tune-X Yamaha Bolt fuel controller, your fuel trim get an extensive recalibration that delivers output and torque you will notice instantly. installation doesnвЂ™t need special expertise, you can complete a Do-it-Yourself setup as long as you are slightly mechanical and electrical minded. This Yamaha Bolt remapper chip wires inline with the signal wire of the stock Intake Air Temperature sensor, which is a standalone sensor or the part of the compact Mass Air Flow (MAF, MAP, TMAP, etc.) sensor, and plugs into the exhaust exhaust air fuel sensor harness on emission-controlled power sources. Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.Yamaha Race Tools Type 2 which allows the quickshifter to be plugged into the bikes wiring harness**.Shift rod for standard shift configuration*.High quality dual direction strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.The Race Tools package allows you to enable Autoblipper, Quickshifter, Engine Warm Up, Pit Speed Limiter and Launch Control in the Stock ECU.Every high performance power train deserves to perform at its peak and the outstanding Smart-Tune-X controller does just that by tapping into your Yamaha Bolt's engine to deliver huge engine performance, mid-end torque and throttle response gains.

#YAMAHA BOLT ECU FLASH FULL#

Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations.ДЄutoblipper Opening and Duration maps are fully configurable per gear. Pit Speed Limiter RPM can be configured.***Д®ngine Warm Up parameters are configurable.*** Launch Control allows you to configure Delay, Launch RPM and Hold Speed. * Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length. ** This harness uses the stock O2 Sensor plugs on the bike's harness, the stock O2 sensor should be removed from the bike and disabled in the WRT software. *** The Pit Speed Limiter / Engine Warm Up requires the purchase of an additional Pit Speed Limiter harness. Woolich Racing Race Tools requires you to Write the ECU. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU.

Yamaha bolt ecu flash